反后坐裝置落錘試驗臺設計——落錘釋放機構設計

1.1萬字 36頁 原創作品，已通過查重系統


畢業設計說明書中文摘要
摘要：本文主要介紹了落錘釋放機構的設計。首先介紹了一下吊具的應用領域，接著說明了設計的任務要求。根據任務要求進行方案的選擇，確定了落錘釋放機構的設計方案，設計一種機械自動脫鉤。對落錘釋放機構進行功能設計，進行原理分析和運動學分析。然后在功能設計的基礎上，對落錘釋放機構進行具體的結構設計，包括鉤桿、頂桿、吊鉤體等零件的尺寸設計和相關校核工作。最后對本次設計進行了簡單的總結。


關鍵詞 落錘釋放機構 吊具 機械自動脫鉤



畢業設計說明書外文摘要

title The design of a recoil system’s drop test bench
——the design of release mechanism of a drop hammer
Abstract
This article mainly introduces the designing process of the drop hammer release
mechanism.The application field of sling is introduced.It illustrates the requirements corresponding to the design task .According to the needs of task schemethe designing scheme of the release mechanism of drop hammer is selected through a scientific process .The design of a mechanical automatic decoupling mechanism is followed. And then function designprinciple analysis and kinematics analysis of the release mechanism of drop hammer is carried out.On the basis of functional designthe concrete structure of drop hammer release mechanism including the hook rod plunger the hook body parts is determined .Finallyit gives a brief summary for this design.

Keywords Hammer release mechanism Sling Mechanical automatic decoupling



目 次
1 緒論 1
1.1 吊具的應用領域 1
1.2 反后坐裝置落錘試驗臺概述 1
1.3 研究內容 1
1.4 研究意義 2
1.5 主要的工作內容 2
2 確定落錘釋放機構的設計方案 3
2.1 落錘釋放機構可行的方案 3
2.2 落錘釋放機構設計方案的確定 5
2.3 本章小結 5
3 落錘釋放機構的力學分析 6
3.1 機械自動脫鉤系統原理 6
3.2 對機構整體的受力分析 6
3.3 本章小結 10
4 落錘釋放機構的技術設計 11
4.1 落錘錘頭與鉤桿的設計 11
4.2 頂桿的尺寸設計及其穩定性校核 14
4.3 銷軸的設計 16
4.4 吊鉤體的設計 17
4.5 彈簧的設計 18
4.6 滑塊的設計 22
4.7 本章小結 22
5 對零件進行強度分析 23
5.1 SolidWorks軟件中的Simulation介紹 23
5.2 模型的導入與應力分析 23
5.3 本章小結 27
總結 28
致謝 29
參考文獻 30