3×100MW火力發電廠電氣設計（電氣二次系統設計）畢業設計

摘 要
根據設計任務書的要求，本次設計為某3×100MW火力發電廠電氣二次系統設計，并繪制相關工程設計圖紙若干。本發電廠有220kV,110kV，10kV三個電壓等級。
本次設計嚴格遵循發電廠電氣部分的設計原則，主要做了以下工作：電氣主接線的選擇、短路電流的計算、發電機與變壓器繼電保護配置、220kV斷路器保護配置等，其中對發電廠主設備的繼電保護將采用微機保護。
本設計以《繼電保護和安全自動裝置技術規程》、《供配電系統設計規范》等規程規范為依據，設計的內容符合國家有關經濟技術政策，所選設備全部為國家推薦的新型產品。
關鍵詞 發電廠，電氣二次系統，繼電保護，微機保護
 

Abstract
According to the design requirements of the mission statement, this design is for secondary electrical circuit of a 3 × 100MW power plant, Which needs us to draw a number of related engineering drawings. The power plant has three voltage levels, Which are 220kV, 110kV, and 10kV.
The design, which strictly follows the principle part of the design of electrical parts of power plants, concrete work, including the calculation of short-circuit current, generator and transformer protection relay configuration, 220kV circuit breaker protection configuration, in which for the main equipments of the power plants, will use the microprocessor based protection.
This design is mainly based on The Design Code for relay protection and security automatic device, The Design Code for Power Supply System, and other standard procedures. So its contents as follows conform to the relevant economic and technical policies, and all the selected equipments the state recommends are new products.
Key words power plants, secondary electrical circuit, relay protection, microprocessor based protection

 
目 錄
摘 要 I
ABSTRACT II
1 緒論 - 1 -
1.1 引言 - 1 -
1.2 原始數據與設計任務 - 2 -
1.3 任務分析 - 3 -
2 電氣主接線設計 - 4 -
2.1 典型主接線概述 - 4 -
2.2 主接線方案比較與確定 - 5 -
3 短路電流計算 - 7 -
3.1 短路電流計算方法 - 7 -
3.2 阻抗標幺值計算 - 7 -
3.3 各短路點的短路電流計算 - 9 -
4 變壓器保護 - 19 -
4.1 變壓器保護配置 - 19 -
4.2 變壓器微機保護 - 19 -
4.3 變壓器保護整定計算 - 20 -
5 發電機保護 - 27 -
5.1 發電機保護配置 - 27 -
5.2 發電機微機保護 - 27 -
5.3 發電機保護整定計算 - 28 -
6 斷路器保護控制系統 - 36 -
6.1 220KV側高壓斷路器選擇 - 36 -
6.2 斷路器失靈保護 - 37 -
6.3 斷路器控制與信號回路 - 38 -
7 母線保護 - 42 -
7.1 微機型母線保護 - 42 -
7.2 母線差動保護 - 42 -
7.3 母聯充電保護 - 44 -
8 結 論 - 45 -
謝 辭 - 47 -
參考文獻 - 48 -
A1.1 變壓器的應用 - 49 -
A1.2 USES OF TRANSFORMERS - 52 -
附錄Ⅱ 工程設計圖紙 - 55 -
A2.1 電氣主接線圖 - 55 -
A2.2 繼電保護配置圖 - 55 -
A2.3 主變壓器保護控制原理圖 - 55 -
A2.4 發電機保護控制原理圖 - 55 -
A2.5 220KV斷路器保護控制原理圖 - 55 -