JH31-63機械壓力機的設計

摘要
通過對機械壓力機的發展現狀的分析，以及參考JH31-63機械壓力機的設計，確定了本課題的主要設計內容。在確定了機械壓力機初步設計方案后，決定采用傳統理論方法對JH31-63機械壓力機傳動系統進行設計、計算、強度校核；采用AutoCAD設計軟件對傳動系統中各主要零部件及總裝圖進行了工程繪圖；在參考了某公司生產的閉式單點機械壓力機傳動系統以及查閱了大量關于傳動系統設計的書籍后，確定傳動系統的設計方案，繪制了傳動系統原理圖，給出了傳動系統的工作說明書，并對其進行了可行性分析，最后對整個設計進行系統分析，得出整個設計切實可行。

關鍵詞  機械壓力機 ；運動及受力分析；傳動系統

Abstract
Through the development of mechanical press on the analysis of current situation and reference for the J31-63 mechanical press design, identified the main design elements of this issue.It is determined that the preliminary design of the mechanical press will be used the traditional mechanical press drive system to design the J31-63 .The decision theory method is used the calculation, strength check and AutoCAD design software on the drive system in all major components and assembly diagram engineering drawing. In reference to a closed two-point produced by mechanical press drive system and a large amount of books on the transmission system after the design to determine the transmission system design, schematic drawing of the transmission system, given the transmission system, job description and analysis of its feasibility, and finally a systematic analysis of the entire design, draw the design is feasible.
keywords   Mechanical press  Movement and Force Analysis  Transmission system

目       錄
1 緒論 1
1．1曲柄壓力機的發展過程 1
1.2 壓力機簡介 3
1.2.1 壓力機的特點和用途 3
1.2.3 曲柄壓力機的基本參數 5
1.3 壓力機工作原理 7
2 曲柄滑塊機構的運動分析與受力分析 9
2.1曲柄滑塊機構的運動分析 9
2.1.1滑塊的位移和曲柄轉角之間的關系 9
2.1.2滑塊的速度和曲柄轉角的關系 10
2.1.3滑塊的加速度和曲柄轉角的關系 11
2.2曲柄滑塊機構的受力分析 11
3 曲軸受力分析 13
3.1理想扭矩 13
3.2摩擦扭矩 15
4 芯軸設計計算 17
5 傳動系統的布置與設計 25
5.1傳動系統的布置 25
5.2傳動級數和各級速比分配 27
6 傳動零件的設計計算 29
6.1齒輪 29
6.2傳動軸 31
7 電動機的選擇與飛輪設計 36
7.1功能組成 36
7.2 飛輪轉動慣量計算及尺寸確定 37
結論 40
致謝 41
參考文獻 42
附錄 43