摘 要

隨著電力電源的快速發展，功能要求越來越高，電源監控系統的智能性也在不斷的更新提高?；诖耍疚脑O(shè)計了智能電源監控系統。
系統采用STC12C5A60S2系列單片機作為微控制器，系統由主監控人機接口與顯示、電流信號的采集、電壓信號的采集、報警電路、繼電器觸點保護電路以及下行通信等模塊組成。電路流檢測模塊實現對交流電壓和電流的不間斷實時檢測，并對電源系統進行實時監測。當發生故障時，進行報警提示，并通過通信總線傳輸?shù)街鞅O(jiān)控單元，從而實現智能監控。
此模塊能夠很好的完成檢測功能，并且具有良好的經濟性。
本文通過對交流檢測模塊的軟硬件進行了相應的設計和調試，完成了畢業設計所要求的任務。

關鍵詞：智能電源監控；STC12C5A60S2單片機；交流檢測及控制。










ABSTRACT

With the rapid development of electric power, the function demand is higher and higher, power monitoring system of intelligent is also in constant updates improve. Based on this, the paper designed a intelligent power monitoring system.
System uses STC12C5A60S2 series microcontroller as micro controller, system by the main monitoring man-machine interface and display, pay current signal collection, voltage signal collection, alarm circuit, relay contacts protection circuit and downlink communication module. Circuit flow of inspection module realize the ac voltage and current detection in real time, uninterrupted power supply system of real-time monitoring. When malfunction happened, alarm prompt, and through communications bus transfers to the main monitoring unit, so as to realize intelligent monitoring.
This module can be good finish detection function, and has good economy.
This article through to exchange detection module the hardware and software of the corresponding design and commissioning, completed the graduation design requirements of the task.
Keywords：Intelligent power monitoring; STC12C5A60S2 microcontroller; Exchange detection and control.




目錄
1 緒論 1
1.1 電力電源的背景及發展 1
1.2 電源監控系統的研究意義 3
1.3 本題主要研究內容 5
2 方案選擇 7
2.1 方案一、利用外擴存儲器的方案 7
2.2 方案二、不需外擴存儲器的方案 8
3 硬件系統設計 10
3.1 微處理器芯片的選型 10
3.2單片機最小系統電路 12
3.3三相交流電流采集電路 14
3.4 三相交流電壓采集電路 16
3.5繼電器觸點保護電路 18
3.6下行通信電路 21
3.7報警保護電路 26
3.8供電電源電路 29
3.9交流檢測模塊電路圖 31
4 軟件系統設計 32
4.1 總體設計思想 32
4.2三相交流監測程序設計 34
4.2.1三相交流電流采集的程序設計 36
4.2.2 三相交流電壓采集的程序設計 37
5 系統的仿真與調試 38
5.1 Keil C51開發系統基本知識 38
5.2 Keil C51 IDE開發仿真環境的設置方法 39
5.3系統軟件的編譯環境 40
5.4系統組裝調試 42
6 結束語 43
參考文獻 44
致 謝 46