電機自拖動裝置設計

摘要

本次畢業設計研究的課題是智能化轉速測量儀。電機在運行過程中，需要對其進行監控，轉速是一個必不可少的一個參數。本系統就是對電機轉速進行測量，并可以和PC機通信，顯示電機的轉速，并觀察電機運行的狀況。
本設計主要用AT89C51作為控制核心，由霍爾傳感器、LED數碼顯、HIN232CPE電平轉換、及RS232構成。詳細介紹了單片機的測量轉速系統及PC機與單片機之間的串行通訊。充分發揮了單片機的性能。本文重點是測量速度并顯示在5位LED數碼管上。
其優點硬件電路簡單，軟件功能完善，測量速度快、精度高、控制系統可靠，性價比較高等特點。
關鍵字：MSC-51（單片機）；轉速傳感器 ；數碼顯示；RS232

Abstract

This design project for graduation’ task is to monitor intellectual tachometer measurement device electrical machinery when it runs, Tachometer is an indispensable parament. And then this system can solve the problem of monitoring tachometer by tachometer, and it can achieve the communication of the machine of PC. 
For adjusting the stability of the electrical machinery when it runs, take notes the record about the tachometer per minutes; draw the coordinate charter between tachometer and time.
This design mainly applies AT89c51 to control core and combine sensor, LED, HIN232CPE, and RS232.this design introduce the system of tachometer measurement of MCU.
The send and receiver of the date take the full use of the natural capacity of MCU. The key of this paper is to measure tachometer and manifest it on LED.
The advantages are simple hardware electrical circuit, perfect software competence, high-speed measurement, high accuracy, reliable control system, relatively high price and other features
Keyword ：MSC-51(One-chip computer)；sensor；tachometer；RS232

目錄

0前言……………………………………………………………………….................................1
1系統功能分析……………………………………………………….... …...........................2
1.1系統功能概述………………………………………………………. …............................ 2
1.1.1系統功能………………………………………………………….. …........... 2
1.1.2 組成及框圖………………………………………………………. …............................2
1.2系統要求及主要內容……………………………………………….. ……….. 2
1.3系統技術指標……………………………………………………….. ……….. 3
2系統總體設計…………………………………………………………. ……….. 4
2.1硬件電路設計思路……………………………………………………............. 4
2.2軟件設計思路......................................................................................................4
3硬件電路設計………………………………………………………………………………..6
3.1 單片機模塊………………………………………………………………………………..6
3.1.1執行元件……………………………………………………………............. .6
3.1.2時鐘電路…………………………………………………………………… ..9
3.1.3復位電路…………………………………………………………………… 10
3.1.4顯示電路…………………………………………………………………… 11
3.2霍爾傳感器簡介............................................................................................... 13
3.2.1霍爾器件概述……………………………………………………………… 13
3.2.2霍爾傳感器的應用………………………………………………………… 14
3.2.3 AH41霍爾開關……………………………………………………………. 15
3.3發送模塊…………………………………………………………………….. 16
3.3.1數據的傳輸………………………………………………………………... 16
3.3.2器件的介紹……………………………………………………………… 16
4 步進電機…………………………………………………………..………… 19
4.1步進電機簡介……………………………………………………………….. 19
4.1.1 步進電機的主要特性……………………………………………….........19
4.2步進電機驅動………………………………………………………………..20
4.3 步進電機驅動系統簡介……………………………………….....................21
4.3.1 步進電機驅動器的特點………………………………………………….21
4.4 國內外研究概況及發展趨勢……………………………………………….22
5軟件設計..............................................................................................................24
5．1單片機轉速程序設計思路及過程………………………………………….24
5.1.1單片機程序設計思路……………………………………………………….24
5.1.2單片機轉速計算程序……………………………………………………….25
5.1.3二-十進制轉換程序………………………………………………………...25
5.1.4單片機顯示程序…………………………………………………………….26
5.2程序設計………………………………………………………………………26
6 系統調試……………………………………………………………………….29
6.1硬件調試………………………………………………………………………29
6.1.1上電前的調試……………………………………………………………….29
6.1.2上電后的調試……………………………………………………………….29
6.2軟件測試………………………………………………………………….......30
6.2.1單片機程序調試思路…………………………………………………….30
6.3綜合調試………………………………………………………………………32
6.4故障分析與解決方案…………………………………………………………32
7程序……………………………………………………………………………...34
8電機微機控制系統的可靠性…………………………………………………...37
8.1電機微機控制系統的故障概述…………………………………………….............37
8.1.1與可靠性有關的幾個概念………………………………………………...............37
8.1.2電機微機控制系統的故障分析…………………………………………………..38
8.2提高電機微機控制系統可靠性的方法……………………………………...40
8.2.1提高硬件可靠性的方法…………………………………………………...40
8.2.2提高軟件可靠性的方法………………………………………………….43
9技術經濟分析……………………………………………………………….... .44
10結論……………………………………………………………………………45
致謝……………………………………………………………………………… 46
參考文獻………………………………………………………………………….47
附錄A譯文……………………………………………………………………….48
附錄B外文文獻………………………………………………………………….56