基于AT89S52單片機的溫度濕度計的設計

目  錄
1 緒論 2
1.1  問題的提出與意義 2
1.2  國內外的發展現狀 2
1.3  研究的目的與方向 2
2 設計分析 3
2.1  設計方案 3
2.2  系統組成 3
2.3  工作原理 4
3 總體設計 4
3.1  主要器件簡介 4
3.2  主要電路模塊 6
3.3  軟件設計編程 8
4 調試 13
結束語 14
致謝 14
參考文獻 14
附錄 16

 
基于AT89S52單片機的溫度濕度計的設計
摘要：采用MSC-51系列單片機中的AT89S51和溫濕度傳感器DHT11的低成本設計溫濕度的檢測系統。由DHT11溫濕度傳感器及LCD1602字符型液晶模塊構成系統顯示模塊，該系統電路簡單、工作穩定、集成度高、調試方便、測量精準度高，具有一定的實用價值與意義。其中測溫濕度監測電路由溫濕度傳感器和預設溫度值比較報警電路組成，用戶根據需要預先輸入預設值，當實際測量的溫濕度大于預設的溫濕度數值時，發出報警信號（蜂鳴器蜂鳴）。
關鍵詞：?jiǎn)纹瑱C(jī); 溫濕度傳感器; 溫濕度檢測系統; AT89S52; DHT11

Based on the Design of Temperature Humidity Indicator of AT89S52 Singlechip
Wang Wei
（Department of Electronic Information Engineering  Supervisor: Shen Wenlong）
Abstract:This design is the use of MSC-51 Series MCU AT89S51 and DHT11 in the low-cost temperature and humidity detection system.The DHT11 temperature and humidity sensor and 1602 constitute a system of character LCD module display module, the system circuit is simple, stable, high level of integration, commissioning convenient, accurate, has some practical value and significance. Temperature and humidity Monitor circuit in which the temperature and humidity sensors and compare the value of the preset temperature alarm circuit, the user input required pre-default value, when the actual temperature and humidity measurements of temperature and humidity is greater than the preset value, an alarm signal (bee Buzzer beep).
Keywords: microcontroller; temperature and humidity sensor; detection system; AT89S52; DHT11