目   錄
摘    要 4
1 前言 5
2 水輪機選型設計 6
2.1 水輪機臺數及型號的選擇 6
2.2 初選額定工況點 7
2.3 確定轉輪直徑 7
2.4額定轉速的確定 8
2.5 效率及單位參數修正值 8
2.6 檢驗所選水輪機的實際工作區域 9
2.7 確定導葉開度 11
2.8 計算額定流量 11
2.9 確定水輪機的吸出高度 11
2.10 計算水輪機飛逸轉速 16
2.11 估算軸向水推力 16
2.12 估算水輪機質量 16
2.13 繪制水輪機運轉綜合特性曲線 17
3 蝸殼水力設計 21
3.1 概述 21
3.2 蝸殼類型的選擇 22
3.3 金屬蝸殼主要參數的確定 22
3.4 金屬蝸殼水力設計計算 23
4 尾水管設計 29
4.1 尾水管的作用及類型 29
4.2尾水管類型的選擇 29
4.3 繪制尾水管水力單線圖 30
5 水輪機導水機構運動圖的繪制 30
5.1 導水機構的作用及類型 30
5.2 繪制導水機構運動圖的目的 30
5.3 徑向式導水機構運動圖的繪制 31
6 水輪機結構設計 35
6.1 概述 35
6.2 轉輪的結構設計 36
6.3 導葉的結構、系列尺寸和軸頸選擇 38
6.4 導葉的傳動機構 38
6.5 導水機構的環形部件設計 39
6.6 真空破壞閥 40
6.7 主軸的設計 41
6.8 軸承的結構 43
6.9 補氣裝置 43
6.10 主軸的密封 44
7 導葉加工圖的繪制 45
8 蝸殼強度計算 46
8.1 對金屬蝸殼的受力分析 46
8.2 編程進行強度計算 49
9 結論 54
總結與體會 55
謝辭 55
參考文獻 56

摘    要

本次設計是在給出仙溪水電站原始資料的情況下，為電站進行水輪機選型設計，并繪制出運轉綜合特性曲線。從最大水頭考慮，初步選定了 和HL220/A153兩個轉輪型號，然后從機組的運行穩定性和經濟性（電站開挖量）對兩個轉輪進行綜合比較分析，最終確定出水輪機型號為 ，機組臺數為兩臺。在此基礎上，完成蝸殼及尾水管的水力設計及單線圖的繪制、導水機構運動圖的繪制、水輪機總裝圖的繪制、水輪機導葉零件圖的繪制以及蝸殼的強度計算等設計任務。
關鍵詞：水輪機；選型設計；結構設計；強度計算

Abstract

Based on the given original data of XianXi hydro plant, the type selection design of this hydropower station is put up, and the performance combined characteristic curve of turbine is plotted. By considering the maximum head, HL240/D41 and HL220/A153 are chosen primarily. Afterwards, the hydraulic turbine type, which is HL220/A153-LJ-140, and the number of units is two, are selected by general comparison and analysis of the stability and economy about the two runners. Based on the result, hydraulic calculation and neat lines of casing and draft tube, the movement drawing of the guide apparatus, the turbine assembly drawing and pivoted guide vane drawing have been accomplished. The intensity calculation of pivoted casing has been fulfilled.
Key words：Hydraulic Turbine; Type Selection Design; Structure Design; Intensity Calculation