鋼結構施工外文翻譯——鋼結構工程施工方案.doc
約26頁DOC格式手機打開展開
鋼結構施工外文翻譯——鋼結構工程施工方案,Ⅰ.a brief account of steel structure workthere will be 6 8t bridge traveling cranes in production hall, welding h-section steel column and beam, structural main...
內容介紹
此文檔由會員 wanli1988go 發布
Ⅰ.A brief account of steel structure work
There will be 6 8t bridge traveling cranes in production hall, welding H-section steel column and beam, structural main material is Q345B, cold bending sheet steel Z-purlin, wall and roof cladding are double-skin pressed steel sheet and thermal insulation wool.
Ⅱ.Characteristic of steel structure work
The single span of the work is 18m, the height of steel column is large, single frame plane external rigidity is very small, so the key point of safety technical control is to guarantee the stability outside the structural plane.
Take out 6 steel columns from grid line 9~14 in the production building, instead of 52.5m space truss as trimmer beam to support the upper structure and crane load, the installation of the space truss is a difficulty point of this work.
Ⅲ.Fabrication of steel structural members
Technical preparations prior fabrication
1. Study and check the design working drawing before fabrication, make shop drawing and get approval from designer then prepare material for fabrication.
一、鋼結構工程概述
生產車間內設有6個8T橋式桁車,鋼柱、鋼梁采用焊接成型的H型鋼,結構主材采用Q345B,檁條采用Z型鋼,墻面采用雙層壓型鋼板+保溫棉的構造,屋面采用鋼承板+保溫板+柔性防水卷材的構造。
二、鋼結構工程的特點
1、該工程單坡最大跨度為18m,鋼柱高度大,單榀框架的平面外剛度極小,吊裝過程中做好保證結構平面外的穩定作為安全技術控制的重點。
2、廠房最大連續24跨,長度方向252m,制作安裝時應注意誤差累計,做好測量控制點,保證整個廠房的安裝精度。
三、鋼構件的制作
(一)、制作前的技術準備
1、鋼結構制作前必須熟悉設計的施工圖,了解設計要求,并審核圖紙,根據藍圖編制加工制作圖,并在得到原設計部門的認可后方可進行備料加工。
2、根據構件類型、數量、用材制定加工計劃和加工程序。
3、編制施工工藝和技術措施,以及對加工用的設備制定檢查維護計劃,使機械設備處于良好狀態。
(二)、主材采購計劃
1、對工程用的材料應進行選定和確認。
2、各種材料均應有質量證明書和出廠合格證。若有疑議則應按國家有關標準的
There will be 6 8t bridge traveling cranes in production hall, welding H-section steel column and beam, structural main material is Q345B, cold bending sheet steel Z-purlin, wall and roof cladding are double-skin pressed steel sheet and thermal insulation wool.
Ⅱ.Characteristic of steel structure work
The single span of the work is 18m, the height of steel column is large, single frame plane external rigidity is very small, so the key point of safety technical control is to guarantee the stability outside the structural plane.
Take out 6 steel columns from grid line 9~14 in the production building, instead of 52.5m space truss as trimmer beam to support the upper structure and crane load, the installation of the space truss is a difficulty point of this work.
Ⅲ.Fabrication of steel structural members
Technical preparations prior fabrication
1. Study and check the design working drawing before fabrication, make shop drawing and get approval from designer then prepare material for fabrication.
一、鋼結構工程概述
生產車間內設有6個8T橋式桁車,鋼柱、鋼梁采用焊接成型的H型鋼,結構主材采用Q345B,檁條采用Z型鋼,墻面采用雙層壓型鋼板+保溫棉的構造,屋面采用鋼承板+保溫板+柔性防水卷材的構造。
二、鋼結構工程的特點
1、該工程單坡最大跨度為18m,鋼柱高度大,單榀框架的平面外剛度極小,吊裝過程中做好保證結構平面外的穩定作為安全技術控制的重點。
2、廠房最大連續24跨,長度方向252m,制作安裝時應注意誤差累計,做好測量控制點,保證整個廠房的安裝精度。
三、鋼構件的制作
(一)、制作前的技術準備
1、鋼結構制作前必須熟悉設計的施工圖,了解設計要求,并審核圖紙,根據藍圖編制加工制作圖,并在得到原設計部門的認可后方可進行備料加工。
2、根據構件類型、數量、用材制定加工計劃和加工程序。
3、編制施工工藝和技術措施,以及對加工用的設備制定檢查維護計劃,使機械設備處于良好狀態。
(二)、主材采購計劃
1、對工程用的材料應進行選定和確認。
2、各種材料均應有質量證明書和出廠合格證。若有疑議則應按國家有關標準的
TA們正在看...
- 中班主題活動教案:《數高樓》教案(附教學反思).doc
- 中班主題活動教案:《春天的電話》教案(附教學反思).doc
- 中班主題活動教案:《有趣的傘游戲》教案.doc
- 中班主題活動教案:《有趣的冰》教案(附教學反思).doc
- 中班主題活動教案:《水》教案(附教學反思).doc
- 中班主題活動教案:《沒長耳朵的小老虎》教案(附教...doc
- 中班主題活動教案:《端午節》教案(附教學反思).doc
- 中班主題活動教案:《蔬菜寶寶》教案(附教學反思).doc
- 中班主題活動教案:一瓶美麗的花教案(附教學反思).doc
- 中班主題活動教案:七彩蠟筆鼠教案(附教學反思).doc