畢業設計：拖拉機變速箱體三面攻螺紋組合機床總體及左主軸箱設計
論文說明書共31頁，字?jǐn)?shù)總計：12252
資料簡介：
外文文獻
中文文獻
A0-被加工零件工序圖.dwg
A3-側蓋補充加工圖.dwg
A3-傳動軸.dwg
A1-攻絲靠模機構.dwg
A3-后蓋補充加工圖.dwg
A0-機床聯系圖.dwg
A4-生產率計算卡.dwg
A0-加工示意圖.dwg
A3-手柄軸.dwg
A3-主軸.dwg
A0-左主軸箱箱體補充加工圖.dwg
A0-左主軸箱裝配圖.dwg
A2-坐標檢查圖.dwg
備份圖紙
畢業論文：拖拉機變速箱體三面攻螺紋組合機床總體及左主軸箱設計.doc
畢業設計開題報告.doc
畢業設計任務書.doc
畢業設計實習報告.doc
畢業設計說明書封面.doc
畢業設計指導教師評價意見及評分表.doc
課題申報表.doc
外文翻譯.doc
摘要.doc
拖拉機變速箱體三面攻螺紋組合機床總體及左主軸箱設計
摘 要：本次設計的題目是拖拉機變速箱體三面攻螺紋組合機床總體及左主軸箱設計。組合機床主軸箱設計，按專用要求進行設計，由通用零件組成，其主要作用是根據被加工零件的要求，安排各主軸位置并將動力和運動由電機或動力部件傳給各主軸，使之得到要求的轉速，機床主軸箱選用500 500,用中間傳動軸帶動主軸傳動。在機體上加工6個滿足深22mm位置公差為0. 4mm尺寸要求的M14螺紋孔,然后加工4個滿足深18mm位置公差為0.2mm尺寸要求的M10螺紋孔，再加工2個滿足深22mm位置公差為0.2mm尺寸要求的M10螺紋孔。總體設計中設置了動力箱、主軸箱、靠模裝置、床身等一系列裝置,并接滿足結構合理,簡單實用的要求.夾具設計的目的是使工件在機床上定位準確,夾緊可靠.由于被加工零件孔數量較多，且間距小，排列分散，在經過大量的設計計算之后，采用了立式單工位的加工方法，同時對12個孔進行攻絲加工。該機床成本低,加工精度高,操作使用方便,減輕了勞動強度并提高了生產效率。
關鍵詞：組合機床；攻絲加工；主軸箱；傳動設計


Design of General of Modular Machine Tool for Tapping Holes on Three-Side of spindle Box and left Headstock
Abstract: The topic of design is the design of general of modular machine tool for tapping holes on three-side of spindle box and left headstock. The design of the headstock of modular machine tool is made up of the common parts which is by special request. As major use is to be processed in accordance with the requirements of parts, arrangements for the location of the spindle. According to the working demands of the worked parts and make it get the speed which is demanded, The headstock is made in size of 500 500. It’s driven by the middle of the spindle drive shaft. The purpose of the general is to be accord with the size request of the deep of 22 mm and the location tolerance of 0.4 mm when processing the screw holes of M14.And then the purpose of the general is to be accord with the size request of the deep of 18 mm and the location tolerance of 0.2 mm when processing the screw holes of M10.The last purpose of the general is to be accord with the size request the deep of 22 mm and the location tolerance of 0.2 mm when processing the screw holes of M10. There are power supply box, spindle box, device of profile modeling, machine bed in general design. It is satisfied with the request that the frame is reasonable, simple and practical. The purpose of the design of jig is that the workpiece positioning in machine tool accuracy and clamping reliable. Hole caused by the processing parts in larger quantities, with scattered, after a large number of design and calculation, adopt the vertical single-stage processing method, processing 12-hole at the same time. The low cost of machine tools, processing and high precision, easy operation, reducing the labor intensity and improve production efficiency.
Key words: Modular machine tool; Tapping processing; Spindle box; Transmission Design
目 錄
1 前言 1
2 組合機床總體設計 3
2.1 總體方案論證 3
3 設計計算 6
3.1 絲錐的切削負荷 6
3.2 攻螺紋扭矩的計算 6
3.3 主軸直徑的確定 7
3.4 切削速度的確定 8
3.5 切削功率的確定 8
3.6 攻螺紋主轉速的計算 10
3.7 確定主軸箱輪廓尺寸 11
3.8 生產率計算 11
3.9 通用部件的選擇 12
4 組合機床左主軸箱設計 14
4.1 繪制左主軸箱設計原始依據圖 14
4.2 主軸、齒輪的確定及動力計算 15
4.3 主軸箱傳動系統的設計與計算 15
4.4 多軸箱坐標計算、繪制坐標檢查圖 18
4.5 齒輪強度校核 20
4.6 傳動軸直徑的確定和軸的強度校核 22
4.7 主軸箱體及其附件的選擇設計 25
5 結論 27
參 考 文 獻 28
致 謝 29
附錄 30