畢業設計 多刀半自動車床主傳動系統的設計
設計論文共60頁，字?jǐn)?shù)總計：15986
資料簡介：
A0-電氣原理圖.dwg
A0-主軸箱總裝配圖.dwg
A1-液壓原理圖.dwg
A2-套杯.dwg
A2-卸荷帶輪.dwg
A3-齒輪Z47.dwg
A3-花鍵軸.dwg
A3-主軸.dwg
畢業設計說明書.doc
扉頁.doc
封皮、目錄、摘要（定）.doc
摘 要

本設計從下達任務起，經過現場調查和查閱文獻資料入手，歷經三個月的時間完成。在設計中，首先根據課題所要求的技術參數確定機床設計中所需要的參數，即原動機的功率、機床主軸箱的轉速數列公比；然后確定機床主軸箱的主傳動系統結構，擬訂機床的結構網和轉速圖；查資料，根據轉速圖確定機床內的各個主要零件的計算轉速，根據計算轉速確定各級傳動的傳動比，根據傳動比來確定各級傳動的齒輪配合的齒輪齒數。根據機床主軸箱的傳動鏈來計算各級轉速的實際值與理論值之間的誤差。在設計中主要是要計算主軸箱里各個零件的選用是否滿足要求以及原動機與主軸箱間的動力傳遞裝置的計算。主軸箱的計算包括摩擦離合器的校核、齒輪的校核、軸的校核、軸承的校核、鍵的校核、主軸的校核計算等。原動機與主軸箱的動力傳遞采用的是帶傳動裝置。最后根據資料和參考同類機床來設計計算機床的電氣和液壓系統，并繪制其原理圖。
關鍵詞：轉速數列； 公比； 結構網； 轉速圖； 計算轉速； 轉速數列公比。
ABSTRACT

This design from descend to reach mission to rise, investigate and check cultural heritage data to commence through the spot, experience successively time to complete for three month. In the design, first according to the technique parameter requested by topic assurance the tool machine design in the parameter needed, namely the power, tool machine principal axis box of prime mover turn soon few rows Mr. a ratio; Then make sure a tool machine principal axis the lord of the box to spread to move system structure, draw up the structure net of tool machine and turn soon diagram; Check data, turn soon according to the calculation of each main spare parts turned soon diagram an assurance inside tool machine, turn soon certain all levels and spread and spread and move a ratio dynamically according to the calculation, according to spread and move ratio and spread number of teeth that the dynamic wheel gear matches with a number to the certain all levels. According to tool machine principal axis box the error margin of which spread to move a chain to compute all levels to turn soon actual value and theories value. At mainly need to compute a principal axis box to choose to use in each spare parts in the design whether satisfy to request and prime mover and principal axis box of the motive deliver the calculation of device. The calculation of principal axis box includes the school of the school pit, principal axis of the school pit, key of the school pit, bearings of the school pit, stalk of school pit, wheel gear of rubbing the clutch to calculate calculate etc.The motive of the prime mover and principal axis box's delivering taking to spread to move device is adoptive. Finally according to data and make reference to the same kind tool machine to design electricity and liquid of computing the tool machine to press system, and draw its principle diagram.
Keywords: Turn soon few rows; Mr. Ratio; Structure net; tachogram; the calculation turns soon; Turning soon few words Mr. a ratio.

目 錄
1前言 ……………………………………………………………………… 1
1.1軸承環卡盤多刀車床的用途 ……………………………………… 1
1.2機床的總體布局 ………………………………………………… 1
1.3機床的主要技術參數 …………………………………………… 1
2國內外卡盤多刀車床分析比較 ……………………………………… 2
2.1 國內外同類機床結構的分析比較 ……………………………… 2
2.2 國內外同類機床結構和精度的分析比較 ……………………… 3
2.2.1 結構特點 …………………………………………………… 3
2.2.2 精度比較 ………………………………………………… 4
3機床的運動設計 ……………………………………………………… 4
3.1主軸極限轉速的確定 …………………………………………… 4
3.2轉速數列公比φ的確定 ……………………………………… 5
3.3主軸轉速級數的確定 ……………………………………………… 6
3.4主電機功率的確定 ………………………………………………… 6
3.5主傳動系統的擬定 ………………………………………………… 7
3.6主軸箱的結構設計 ………………………………………………… 8
3.7確定各軸的計算轉速 ……………………………………………… 9
3.8確定各級傳動的傳動比 …………………………………………… 9
3.9查表確定各配對齒輪齒數 ……………………………………… 10
3.10三角膠帶帶輪直徑計算 ……………………………………… 10
3.11各級轉速的實際值 …………………………………………… 12
3.12轉速誤差 ……………………………………………………… 13
4主要零件的設計計算 ……………………………………………… 14
4.1三角膠帶的傳動設計計算 …………………………………… 14
4.2傳動裝置的運動、動力參數的計算 ………………………… 16
4.3摩擦片離合器的計算 ………………………………………… 17
4.4齒輪的計算 ………………………………………………… 18
4.4.1齒輪模數的估算 …..