畢業設計 氣門搖臂軸支座工藝規程及銑Ф16孔兩端面的夾具設計


圖紙資料：
A3—毛坯圖.dwg
A3—氣門搖臂軸支座零件圖.dwg
工序卡片1.dwg
工序卡片2.dwg
工序卡片3.dwg
工序卡片4.dwg
工序卡片5.dwg
工序卡片6.dwg
工序卡片7.dwg
工藝過程卡.dwg
畢業設計說明書.doc



摘 要


搖臂軸是柴油機支撐氣門搖臂，內有油道的輸送潤滑油。搖臂軸支座是用于將搖臂軸固定在柴油機上，為了加強搖臂軸支座的定位，在其底部螺栓孔處有定位凸臺，使其定位在缸蓋螺栓孔內。
零件的材料為HT200，應采用鑄件，由于零件為中批生產，其輪廓尺寸也不大。故可采用鑄造成型。這對提高生產率，保證加工質量也是有利的。
為了提高勞動生產率，保證加工質量，降低勞動強度，需設計專用夾具。由于本零件在組合機床上經過多數工序操作，為其設計專用夾具可大大縮短加工各工序間的時間間隔，提高勞動生產率。



關鍵詞:搖臂軸；工藝規程；專用夾具




ABSTRACT


The valve refers to entering the valve and exhaust valve of the cylinder. Enter valve connect inlet manifold whether engine used for , suck , mix angry entry of (or fresh air ) directly; The exhaust valve is connecting the exhaust manifold, it is the engine that discharges the export which burns the waste gas .
Engine each valve that cylinder have count, have two valve, 3 valves, several kinds of four valves and five valves .
It is a important factor to determine performance quality of the engine to enter the efficiency of exhausting, the pace of reciprocating motion of the piston is very fast when the engine runs well, transfer to in 3000 / rotational speed for minute lay engine finish every one enter angry or exhaust the time of the journey is 0.04 seconds, if you want to suck into or discharge the valid area that more gas will increase into , exhaust within such short time. Then some engines adopt many valve technology.
The rocker shaft is that the diesel engine supports the valve rocker, there is transport lubricating oil of the oil passageway inside. Rocker shaft prop up flat used for , fix rocker shaft on diesel engine , for strengthen rocker shaft localization to prop up flat, orient the protruding platform in its bottom of bolt hole places , make it make a reservation in the jar cover the bolt hole.

keyword : Valve ; Rocker shaft; Jig




















目 錄


1 零件的分析………………………………………………………………………16
1.1 零件的作用………………………………………………………………16
1.2 零件的工藝分析…………………………………………………………16
2 工藝規程設計……………………………………………………………………17
2.1確定毛坯的制造形式………………………………………………………17
2.2基面的選擇…………………………………………………………………17
2.3 制訂工藝路線………………………………………………………………17
2.4機械加工余量、工序尺寸及毛坯尺寸的確定……………………………23
2.5確定切削用量及基本工時…………………………………………………29
3 夾具設計…………………………………………………………………………31
3.1 問題的提出 ………………………………………………………………31
3.2 夾具設計 ………………………………………………………………31
參考文獻 …………………………………………………………………………34
致謝 ………………………………………………………………………………35
附錄 ………………………………………………………………………………36