金剛石工具性能檢測系統（機械執行部分）
1.4萬字 29頁



目 錄

第一章 引 言 1
第二章 金剛石鉆頭及其工作環境簡介 2
2.1 鉆壓選擇 2
2.2 轉速選擇 3
2.3 沖洗液泵量 4

第三章 系統總體結構設計 6
3.1 運動功能分配 6
3.2 結構布局設計 6
3.3 機床總體結構的概略形狀與尺寸設計 6

第四章 系統動力系統設計 7

第五章 液壓進給系統設計 10
5.1 液壓缸參數設計及選用 10
5.2 液壓泵的計算選用 13
5.3 油箱的設計選用 13

第六章 導軌及滾珠絲杠設計 16
6.1 導軌的功能設計及應用 16
6.2 滾珠絲杠設計計算 18

第七章 系統機架的結構尺寸設計 25

結 束 語 26

致謝詞 27

參考文獻 28

附錄一…………………………………………………………………………………29

附錄二…………………………………………………………………………………30



摘 要

本文設計的是金剛石工具性能檢測系統的一部分，即機械執行系統。主要完成鉆頭的鉆進過程。鑒于其需要完成的運動和機床類似，故采用的是類似機床的總體布局。包括機體、立柱、橫梁、工作臺以及機座支承機構。
論文劃分為七個章節，每個章節又細分為幾個不同部分。第一章為序言，主要敘述課題的意義以及系統所要完成的功能。第二章介紹金剛石鉆頭及其工作環境分析，為系統選擇合適的鉆壓、鉆速和沖洗液量。以后幾章則分別詳細介紹了設計總體方案，主動力參數及傳動設計，液壓給進系統設計，滾動導軌及滾珠絲杠的選用計算，機座支承機構的設計計算等。
系統有三個方向的運動趨勢，即橫梁沿立柱上下方向的運動，工作臺底層沿水平方向的運動，工作臺沿前后方向的運動。其中，橫梁和固定其上的電機以及鉆頭沿立柱的運動是由液壓缸驅動的。工作臺下層沿水平方向滾動導軌的運動是由一個小電機驅動滾珠絲杠帶動的。由于工作臺前后方向的運動不常用，而且推力不需要很大，故頂層工作臺采用手柄人力驅動。
鉆頭主軸的旋轉運動由安裝在橫梁上的三相交流電機驅動?？刹捎米冾l方式調速。整體結構簡圖見正文。


關鍵詞：金剛石工具 變頻 滾珠絲杠



Abstract
What this text designed is a part of diamond tool performance detection system, namely mechanical executive system. Finish the creeping into the course of the bit mainly. Seeing that its sport and lathe needing to be finished are similar, so it was the total arrangement which is similar to the lathe that adopted. Including the organism , post , crossbeam , workingbench and machine seat support the organization.
The thesis is divided into seven chapters, each chapter is subdivided into several different parts again. Chapter one a preamble, narrate the meaning of the subject and function finished of system mainly. Chapter two introduce the diamond bit and working environmental analysis , choose the suitable bit pressure , bore speed and amount of liquid developed for the system. Several rules and regulations differentiate the detailed introduction and design the overall scheme afterwards, initiative strength parameter and transmission will be designed, hydraulic pressure is it enter system design , roll guide and ball exertion of guide screw calculate to give, machine flat support design of organization calculate etc..
The system has the sport trends of three directions, namely the sport along the upper and lower directions of the post of crossbeam , workingbench sport when there is in horizontal direction ground floor,workingbench along in front and at the back of direction move. Among them, crossbeam and regular electrical machinery and bit that have their to that jar urge hydraulic pressure have along sport of post. Workingbench lower floor roll sport of guide to urge ball to be that guide screw drive by one light electrical machinery in horizontal direction. Because the sport of the direction is not daily in front and at the back of the workingbench, and thrust did not need very big , so the workingbench of top floor adopts the manpower drive of handles.
Bit rotation sport of main shaft install three phases at crossbeam exchange electrical machinery urge. Can adopt the frequency conversion way to adjust the speed . See the text in whole structure sketch .


Keyword: Diamond tool Frequency conversion Ball guide screw




參考文獻：
[1] 王生主編，鉆孔工程，北京：地質出版社，2002
[2] 徐灝主編，機械設計手冊，北京：機械工業出版社，1992
[3] 機電一體化技術手冊編委會，機電一體化技術手冊，機械工業出版社