塑料夾子注塑模具設計

9300字
自己原創的畢業論文，已經通過校內系統檢測，重復率低，僅在本站獨家出售，大家放心下載使用

摘要 本次畢業設計是讓我們綜合運用機械制造和模具設計中的基本理論，把課本知識與工程問題相結合，在掌握一定的設計方法體系和規范的前提下，運用相關軟件和手冊、圖表等技術資料，擬定注塑模具的設計方案，完成模具的結構設計，著重培養我們的創新能力。題目為塑料夾子的注塑模具設計。在設計過程中，首先運用UG/CAD等繪圖軟件進行繪制，然后選用注塑機型號和塑件材料，接著設計分模面，型腔數目，澆注系統，導向機構，脫模機構，溫度調節系統，排氣系統等，并對此進行相關計算，最后對設計的模具進行試模。在此次設計中，注塑機型號選用SYS—10；塑件材料選用聚丙烯；型腔數目為一模一腔；澆注系統中的澆口選用點澆口；導向機構為模具型腔四周互相配合的4對導柱和導套；脫模機構選用簡單脫模機構中的推桿脫模機構；溫度調節系統為圍繞塑件的冷卻水路；由于模具為小型模具，且分模面適宜，不必設計排氣系統。經相關計算和校核后，該模具能夠達到要求。

關鍵詞：塑料模具 注薂@尚� 塑料夾子

Injection mold design of the plastic clips

Abstract The graduation project is to make our integrated use of machinery and mold design of the basic theory, the textbook knowledge and engineering problems combined under master certain design methodology and specification of the premise, the use of relevant software and manuals, charts and other technical information intended injection mold design, mold design completed, with emphasis on cultivating our ability to innovate. The topic is the plastic injection mold design of clip. In the design process, first we use UG / CAD drawing software for drawing, and then we choose the type and plastic injection molding machine materials, then we design parting surface, number of cavities, pouring system, guiding mechanism, stripping mechanism, temperature control system , exhaust system, etc., and we make correlation calculation, finally we test mold design mode. In this design, the injection molding machine model selection is SYS-10; plastic material selection is polypropylene; the number of cavity is a cavity of a mold; pouring gate system selection is point gate; oriented institutions is around each mold cavity with the four pairs of guide posts and bushings; ejection mechanism chosen is simple stripping mechanism putter release mechanism; temperature control system is the cooling water around the plastic parts; due to the mold is small mold, and parting surface is suitable, we do not need to design the exhaust system. After the relevant calculations and checking, the mold can meet the requirements.

Key words: plastic mold injection molding plastic clips


目錄
第一章 緒論 1
1.1 現代模具工業的發展 1
1.2 注塑模具在我國的現狀 1
1.3 注塑模具在我國的發展趨勢 2
1.4 設計目的 2
第二章 塑件的結構分析及選材 3
2.1 塑件的結構分析 3
2.1.1 技術要求 3
2.1.2 塑件結構分析及選材 4
2.2 聚丙烯的相關資料 4
2.2.1 性能 4
2.2.2 成形特性 4
2.2.3 力學性能 5
2.2.4 成形條件 5
2.2.5 成形注意事項 6
第三章 方案的設計 7
3.1 型腔數目的確定及排布 7
3.2 分模面的選擇 7
3.2.1 分模面的選擇原則 7
3.2.2 分模面的確定 8
3.3 注塑機的選擇與校核 8
3.3.1 注塑機的選擇 8
3.3.2 注塑機的校核 9
3.4 澆注系統的設計 11
3.4.1 澆注系統的設計原則 11
3.4.2 主流道重要尺寸參數 11
3.4.3 澆口的選擇 11
3.5 成形零件設計 12
3.6 合模導向和定位機構 13
3.7 脫模機構設計 14
3.8 模具的溫度調節系統 14
3.9 排氣系統的設計 15
3.10 模架的設計 16
3.11 模具的裝配圖 16
第四章 模具開模合模過程 19
結論 20
致謝 21
參考文獻 22