摘要
傳統的工業縫紉機大多使用離合器調速感應電機，系統調速范圍窄，位置控制困難，自動化程度低。隨著技術的進步，縫紉機的驅動方式從傳統的機械類產品向機電一體化產品過度。永磁無刷電機是隨著電力電子技術的發展而出現的一種新型電機，它具有交流電機的結構簡單、運行可靠、維護方便的特點，又具有直流電機的良好的調速特性，現今已廣泛應用于各種調速場合。本文針對無刷電機在現在縫紉工業中的應用，介紹了一種無刷電機的控制方法。根據工業縫紉機要求啟動快、制動快、工作過程要求轉速穩定等特點，設計了帶有轉速、電流雙閉環的調速系統，以PI調節器為轉速調節器，電流調節器 也用PI調節器，以TL494為PWM脈沖產生芯片，經過綜合邏輯電路加上位置反饋信號，由IR2130驅動電機的功率開關。主要內容包括PWM生成電路和功率開關器件、綜合邏輯電路的選擇，以及驅動電路保護電路的設計等，還有整個調速系統的MATLAB仿真，仿真波形的分析。通過對不同控制方式的仿真，波形的分析選擇較好的控制方式，仿真結果表明系統有較好的可靠性、穩定性和動態性能。

關鍵詞：縫紉機 無刷直流電機 PWM調速 MATLAB仿真

















Abstract
The traditional industry sewing machine mostly uses the coupling to modulate velocity the asynchronous motor, the system velocity modulation scope is narrow, the position control difficulty, the automatization degree low. Along with technical progress, sewing machine drive type from traditional machinery class product to integration of machinery product excessively. Permanent magnetism brushless dc motor is one kind of new electrical machinery , which appears along with the electric power electronic technology development, it has the ac motor’s structure simply, the movement reliable, the maintenance convenient characteristic, also has the direct current machine good velocity modulation characteristic, nowadays widely has applied in each kind of velocity modulation situation. This paper aim at the Brushless DC Motor be applied in the sewing industry, introduce a new control method of BLDC. Based on Industry Sartorius’ characteristic, such as start-up rapidness, brake rapidness, work process rotate speed level off and so on, design one system with speed and current adjuster, the speed adjuster is PID and the current adjuster is PI , use the TL494 chip generate PWM pulse , pass the synthesis logic circuit and the feedback of rotor’s location through IR2130 drive the power switch . Mostly content consist of PWM generate circuit , synthesis logic circuit, power switch and drive circuit and so on , also entire system’s MATLAB emulate and the undee analysis . Via imitate of different control manner, the undee analysis, and then choose the best control manner. By the emulation indicate the entire system have preferable reliability, stability and dynamic capability.

Key words: sewing machine brushless DC motor modulate velocity by PWM MATLAB simulation













目錄
第一章 緒論 1
第二章 縫紉機及電機的工作特點和調節器的選擇 2
2.1縫紉機的工作特點分析及電機選擇 2
2.2無刷直流電機的結構及工作原理 2
2.3控制方案 3
2.4調節器選擇及動態參數設計 4
2.4.1電流調節器的設計 5
2.4.2轉速調節器的設計 7
第三章 控制系統設計 10
3.1位置檢測電路 10
3.2轉速檢測電路 11
3.3轉速調節器 13
3.4 PWM生成電路及電流調節器 13
3.5綜合邏輯電路 15
3.6驅動電路 16
3.7各相導通信號產生電路 18
3.8系統整體電路圖 19
3.9 系統的工作原理 19
第四章 系統仿真及分析 22
4.1采用兩相導通方式 23
4.2三相導通方式 25
第五章 結論和展望 29
致謝 30
參考文獻 31