摘要
自20世紀70年代以來，通過對交流調速控制技術的不斷深入研究與完善，異步電機的交流調速控制系統正逐步取代傳統的直流調速系統，特別是矢量控制變頻調速控制技術更是具有不可比擬的使用價值，并且交流調速技術可以帶來可觀的，對推進國民經濟的增長起著舉足輕重的作用。
本課題深入研究矢量控制、SVPWM調制方式及其DSP實現方法。在現有的交流變頻調速的基礎上展開拓展，從硬件上入手，對現有的交流變頻調速系統的控制部分做出一些改進，加入CPLD，采用矢量控制原理，并對變頻調速系統進行SIMULINK的軟件仿真，驗證系統的可行性與優越性。
本系統采用DSPTMS320LF2407A為控制核心來完成算法，監控整個系統的運行狀態，確保系統的安全運行，系統采用矢量控制原理，而CPLD則針對目前存在一般變頻調速系統所存在的SVPWM波的死區時間問題來進行系統的改善，將最小脈沖寬度做了限制，保證逆變輸出環節同向上下橋臂不會同時通斷，對系統進行保護，嘗試從硬件上解決在算法上不易實現對脈沖寬度控制的問題，大大的提高了系統的效率和可靠性。同時CPLD還用來控制DSP與外部設備的時序及控制邏輯,將不同芯片的地址總線，數據總線、片選、使能、讀寫引腳直接接至CPLD管腳上通過CPLD編程即可方便的實現器件之間的通訊，大大的提高了系統的效率和可靠性。
基于實驗的結果可以證明本文提出的基于DSP的優化交流變頻調速器的軟硬件設計是成功的，其結構簡單，性能良好，運行穩定，抗干擾能力強，具有一定的先進型、新穎性、實用性，為今后開發高性能的矢量控制系統做出一定貢獻。
關鍵詞 ：異步電機；變頻調速；DSP；SVPWM；CPLD





Abstract
Since the nineteen seventies, through the technology of AC speed control further study and improve, asynchronous motor AC speed control system is gradually replacing the traditional DC speed regulating system, in particular the vector control variable frequency speed control technology is incomparable value. and the technology of AC speed regulation can bring considerable, to advance the growth of the national economy play a decisive role.
This topic in depth study of SVPWM modulation and its implementation in DSP. From the hardware proceed with, the existing variable frequency speed regulation system was improved, join CPLD, the vector control principle, and the integrity of the variable frequency speed regulation system for SIMULINK software simulation, verified the feasibility and superiority of the system.
The system uses DSPTMS320LF2407A as the control core to complete the algorithm, monitoring the working state of the whole system, ensure the safe operation of the system, the system uses the vector control principle, and the CPLD is at present general variable frequency speed regulation system the SVPWM wave of the dead time to the improvement of the system, the minimum pulse width have been restricted, to ensure inverter output link to upper and lower bridge arms not simultaneously on-off, system protection, try from the hardware address in the algorithm is not easy to realize pulse width control problems, greatly improve the system efficiency and reliability. At the same time, CPLD is also used to control the DSP and the external equipment timing and control logic, different chip address bus, data bus, a chip select, enable, read and write pin is directly connected to the CPLD pin through the CPLD programming can be convenient to realize the communication between devices, greatly improve the system efficiency and reliability.
Experiments show that the proposed DSP based optimization of AC frequency conversion speed regulator of the hardware and software design is successful, and has the advantages of simple structure, good performance, stable operation, strong anti-interference ability, has certain advanced type, novelty, practicality, for the future development of the high performance vector control system to make some contribution.
Key words ：induction motor; frequency control; DSP; SVPWM; CPLD



目錄
摘要 I
Abstract II
目錄 III
第1章 緒論 1
1.1研究背景和意義 1
1.2變頻調速技術的發展 3
1.3 研究的內容 4
第2章 異步電機變頻調速矢量控制的基本原理 6
2.1 變頻調速的基本原理 6
2.1.1 異步電機的調速方法 6
2.1.2 變頻調速的控制方法 7
2.1.3 變頻設備的分類 8
2.2 坐標變換 10
2.2.1 3s/2s變換(Clarke變換) 10
2.2.2 2s/2r變換（Park變換） 11
2.3 三相異步電機的數學建模 12
2.3.1兩相同步旋轉坐標系下異步電動機的數學建模 12
2.3.2 異步電動機在兩相靜止坐標系上的數學模型 13
2.3.3 三相異步電動機在兩相坐標系下的狀態方程 13
2.4 矢量控制基本原理 15
2.5 PWM技術 18
2.5.1 SPWM 18
2.5.2 SVPWM 19
2.5.3 SPWM與SVPWM相結合算法 23
2.5.4 Matlab仿真SVPWM輸出波形 27
2.5.5電流轉速轉矩仿真結果 31
2.6本章小節 34
第3章 控制系統硬件設計 35
3.1 控制電路的設計 35
3.1.1 數字信號處理器（DSP） 35
3.1.2 CPLD邏輯功能 42
3.2 其他外圍電路 46
3.2.1 存儲器擴展 46
3.2.2 電源設計 48
3.2.3 通訊模塊 49
3.2.4鍵盤輸入接口電路和LED顯示電路設計 50
3.2.5 EEPROM 51
3.2.6 看門狗電路 52
3.3本章小節 52
第4章 系統軟件設計 54
4.1 DSP和CPLD的開發流程及環境 54
4.2 系統主程序 56
4.3 子模塊程序設計 58
4.3.1 定時器中斷程序 58
4.3.2 故障保護中斷程序 58
4.3.3 鍵盤掃描程序..