論文標準WORD格式排版 共 92頁 45995字

摘 要
設計以凌陽單片機SPCE0601A為核心，并配以適當?shù)耐鈬酒c接口電路實現變壓器的溫度監控。系統采用多組風機對油浸風冷式變壓器降溫，變壓器油溫由預埋在變壓器油中的鉑電阻采集，將采集到的油溫在就地和遠端實時顯示，溫度的顯示由LED數碼管實現。當控制變壓器的油溫大于上限溫度值時，投入全部風機；當油溫低于下限溫度值時，停止全部風機的運行；變壓器的油溫介于上限值和下限值之間時,風機按工藝要求運行?？删幊蘎F無線收發器芯片CC1000實現主從機之間的數據傳輸，使中心控制室及時掌握變壓器風機的運行狀況，實現遠程溫度監控。風機出現故障時，相應的發光二極管點亮,并且報警電路發出報警信號。系統要具備完善的過壓、過載、缺相檢測和保護功能。

關鍵詞： SPCE061A ; 無線通信; 變壓器 ;溫度監控

Abstract
This design is based on the Sunplus MCU SPCE0601A , and go together with the appropriate outer circle chip and interface electric circuit to carry out supervise and control oil temperature transformer on the spot and at the long-distance .This system adopts several group electromotor to cool down the temperature of the transformer.The temperature is collected by the temperature transducer of the platinum resistance , The temperature that is gathered will display at right on the spot and at the long-distance . the manifestation of the temperature is realized by the LED figures tube. When the oil temperature of the control transformer is bigger than the upper limit temperature enactmented , throw in all several group electromotor to run ;But when the oil temperature is low in the least temperature value, stop all movements of several group electromotor .When system circulated normally, each three sets of autos threw in movement by turn in six sets of the six group electromotor .The programmable RF wireless transceiver chip CC1000 carries out a lord to deliver from the data between the main single chip and contronl room , making the center control room master the condition of the transformer in time, carrying out supervise and control of the long-distance . when the wind motor appeared to break down ,LED gave out light , and give out alarm. Meanwhile, protection circuit(including voltage, over loading, lacking electrical wire) has been designed for system.

Key Words： SPCE061 A ； Wireless Communication; Transformer; Temperature Monitoring and Control

目 錄
緒 論 III
第1章 設計任務和要求1
1.1 設計任務1
1.2 設計實現的功能1
1.3 主要技術參數與性能指標2
第2章 系統方案的設計3
2.1 方案的提出3
2.2 方案的論證4
2.3 系統工作原理6
第3章 硬件電路設計9
3.1 從機設計9
3.2 主電路設計12
3.2.1 風機的選型13
3.2.2 低壓斷路器的選擇和應用14
3.3 自動與手動控制電路的設計16
3.4 驅動電路的設計17
3.5 LED顯示電路的設計18
3.6 無線數傳通訊電路的設計20
3.7 保護電路的設計23
3.7.1 過壓檢測與保護24
3.7.2 過載檢測與保護27
3.7.3 缺相檢測與保護31
3.8 故障顯示34
3.9 報警電路37
3.10 遠傳開關的設計37
3.11 電源的設計38
第4章 軟件設計41
4.1 軟件結構與軟件設計思想41
4.2 程序流程圖47
第五章 設計總結51
參考文獻52
英文資料及其翻譯53
致 謝74
附 錄75
附錄1 元器件明細表75
附錄2 程序清單79