摘要

此次畢業設計的主要內容有兩個，一個是設計出一個能夠控制四層樓電梯運動的程序,根據平時所知道的,四層樓電梯分為在1層,2層,3層,4層四個樓層?？繒r(shí)的其他樓層呼叫的種種情況.這其中也包括了兩層同時呼叫以及三層同時呼叫.另一個主要任務是設計出電梯的幾個主要部件的零件圖以及裝配圖.其中我主要通過可編程控制器(PLC)來實現四層樓電梯的啟停以及那些呼叫的情況.而在電梯的機械部分設計上,我主要將重點放在了電梯的開門機,曳引機以及控制柜上.當然,轎廂,對重這些部件的尺寸也涉及在內.我運用所學知識獨立完成了四層樓電梯的機械以及電方面的設計.

關鍵詞: 電梯,可編程控制器(PLC),開門機,曳引機,控制柜

Four building elevator design

Abstract

There are two primary coverages in this graduation project, one is to design a procedure which can control this four building elevator. According to which usually knew, four building elevator divides into at one, two, three, four these four floors when other floors call all sorts of situations. This has also included two simultaneous calls as well as three simultaneous calls. Another primary mission is to design the several major components’ detail drawings as well as assembly drawings on the elevator. And I mainly realized the four building elevator’s starting and stoping and those call situations through the programmable controller (PLC). But on the design of the elevator’s mechanical part, I put the emphasis on elevator’s door opener, tactor and cntrol cubicle. Of course, sdan theater box, weight these parts’ sizes also in it. I used knowledge which I have studied to complete the design on mchinery as well as electricity aspect of the four building elevator by my ownself.

Keywords: elevator, programmable controller (PLC), door opener, tactor, control cubicle

目錄

一. 畢業設計課題介紹5
二. 四層樓電梯PLC控制及程序分析7
1. 操作部分控制.7
2. 邏輯分析.7
3. 硬件設計.7
4. 電梯的工作示意圖.8
5. 電梯的I/O接口圖.9
6. 四層樓電梯的情況分析.9
7. PLC程序部分的小結.18
三. 電梯主要部件結構及功能介紹18
1. 電梯曳引系統18
2. 控制柜31
3. 門系統34
4. 對重37
5. 轎廂38
6. 機械部分小結38
四. 畢業設計總結39
五. 參考文獻40
六. 附錄
1. 四層樓電梯控制程序
2. 四層樓電梯梯形圖
3. 主要零部件的裝配圖以及零件圖