畢業設計：主纜放線盤雙層線盤的設計主纜放線盤雙層線盤的設計（含solidworks三維圖）
論文說明書共36頁，字?jǐn)?shù)總計：20309
資料簡介：
（含solidworks三維圖）
A0-雙層線盤總裝配圖.dwg
A2-上轉盤.dwg
A2-下轉盤.dwg
A3-底座.dwg
A3-上剎車?yán)瓧U.dwg
A3-手輪.dwg
A3-透蓋.dwg
A3-外圍護欄.dwg
A3-蝸桿軸.dwg
A3-蝸輪.dwg
A3-下剎車.dwg
A3-軸承座.dwg
A3-主軸.dwg
A4-翻板.dwg
A4-上盤中心筒.dwg
A4-下剎車轉桿.dwg
A4-下轉盤中心筒.dwg
畢業設計（論文）：主纜放線盤雙層線盤的設計.docx
畢業設計(論文)進度計劃表：主纜放線盤雙層線盤的設計.doc
畢業設計(論文)開題報告：主纜放線盤雙層線盤的設計.doc
畢業設計(論文)任務書：主纜放線盤雙層線盤的設計.doc
翻譯原文.pdf
翻譯中文：主纜放線盤雙層線盤的設計.docx
摘 要
　　　
　　　隨著經濟的發展，節省空間，提高生產效率，在生產上越來越重要，纜索的生產，由于場地有限，生產量增多，需設計一種雙層線盤，本課題的具體任務如下：1、課題的調研、資料的獲取、有關知識的準備等 。2、分析雙層線盤的運動要求，整體結構規劃和設計。3、能夠滿足雙層線盤放線方便，實現上盤和下盤運動互不干涉，分開制動；設計傳動裝置，當下盤線用完時，上盤線容易下放到下盤。4、完成雙層線盤結構設計。5、進行必要的強度和結構受力分析。
　　　研究的初期，要進行調研，線圈的重量，大小，轉盤運轉的速度，需要達到的要求，單層線盤的設計結構，材料。雙層線盤的設計是精益生產的一小部分，是下料生產線的主要部分。設計雙層線盤就是為了減少時間和空間上的浪費，同時還可以加大生產量。最終設計的結構如圖2.4所示，采用蝸輪蝸桿傳動裝置來下放線盤，各個結構大部分運用了型鋼加工而成或焊接組成的。
關鍵詞：雙層線盤；分開制動；蝸輪蝸桿；精益生產

　　　　Abstract
　　　
　　　With the development of economy, saving a space and improving the production efficiency are more and more important in the production. Due to the limited space and increased production, the production of cable needs to design a kind of double the wire disc. the subject of the specific task as follows: 1.The subject of research, data acquisition, the preparation of knowledge. 2. Double the wire disc movement analysis requirements and the overall structure planning and design. 3. Can satisfy the double line dish of pay-off is convenient, which can realize the plate and the footwall on mutual non-interference movement, separate braking; Design transmission device, when footwall line is used up, the upper plate can put down on the line. 4. Complete double the wire disc structure design. 5. Make the necessary strength and the structure stress analysis.
　　　In the early stages of the study, I want to undertake investigation and research, such as the weight of the coil, the size, the speed of the rotary operation, the requirements of the need to achieve, single line dish design structure, material. Double the wire disc design is a small part of the lean production; the material is the main part of the production line. Design double the wire disc is to reduce the waste of time and space, also can increase the production. The structure of the final design shown in figure 2.4, people can use the worm gear and worm drive devices to put down the wire, each of the steel structure by processing from or welding of.
Key words：Double the wire disc; separate braking; worm and worm wheel; lean production

目 錄
　　　
引言 1
1 雙層線盤的設計起源 2
　　1.1精益生產的介紹 2
　　1.2雙層線盤的作用 4
2 機械方案的設計 6
　　2.1 初期的調研 6
　　2.2 總體方案的設計 6
3 雙層線盤的結構設計與分析 9
　　3.1 剎車的設計 9
　　3.2 上轉盤的設計 10
　　3.3 下轉盤的設計 13
　　3.4 底座的設計 14
　　3.5外圍護欄的設計 15
　　3.6 主軸的設計與分析 15
4 蝸輪蝸桿的設計與計算 18
　　4.1 蝸輪蝸桿的結構設計與數據分析 18
4.1.1蝸輪蝸桿的相關選擇 19
4.1.2蝸輪蝸桿尺寸的計算 20
　　4.2 蝸桿的設計與校核 21
4.2.1蝸桿軸的設計計算 21
4.2.2蝸桿軸的校核 23
　　4.3蝸輪設計與校核 25
　　4.4其他器件的選擇 26
5結論 29
謝詞 30
參考文獻 31