畢業設計 撥叉80-08的加工工藝（含鏜鉆銑3套夾具設計）
論文說明書共43頁，字?jǐn)?shù)總計：11846
資料簡介：
摘要1.doc
摘要2.doc
畢業設計說明書：撥叉80-08的加工工藝.doc
機械加工工序卡片1.dwg
機械加工工序卡片2.dwg
機械加工工藝過程卡片.dwg
A0-鉆孔夾具裝配圖.dwg
A2-鉆孔夾具體.dwg
A1-銑槽夾具體.dwg
A1-鏜孔夾具體.dwg
A1-銑槽夾具裝配圖.dwg
A0-鏜孔夾具裝配圖.dwg
摘 要

本次設計是車床變速箱中拔叉零件的加工工藝規程及一些工序的專用夾具設計。此拔叉零件的結構較為復雜，其加工的地方主要是孔和平面。本設計先加工孔后加工面。將孔與平面的加工明確劃分成粗加工和精加工階段以保證它們的加工精度?；鶞?zhǔn)選擇以拔叉右面的最大的平面作為粗基準，來加工中間的通孔，然后以此加工過的孔作為精基準。主要加工工序安排是先以中心孔定位加工出頂平面和右側平面以及下面的大孔的兩平面，再以中心孔定位加工出下端的大孔。加工時是用鏜床鏜孔。最后以這兩個孔為基準，分別加工右側的槽和頂面的螺紋底孔。整個加工過程選用了鉆床、銑床和鏜床。工件在機床上定位夾緊選用專用夾具，夾緊方式為手動夾緊，夾緊可靠，操作方便。因此生產效率較高，適用于大批量、流水線上加工。能夠滿足設計要求。


關鍵詞 加工工藝，定位，夾緊，專用夾具
ABSTRACT

This design is a lather to become soon an appropriation for inside pulling out fork spare parts processing craft rules distance and some work prefaces tongs design.This pull out the construction of the fork spare parts than for complicacy, its the place that process is a peaceful in bore primarily.This design processes after processing first the bore.Process with flat surface the clear and definite dividing the line the bore the coarseness processes to process with the nicety the stage to guarantee their process the precise degree.The basis choice to pull out rough basis of conduct and actions of the biggest flat surface of the right in fork, process the in the center in general use bore, then be used as the precise basis with the bore that processed.Processing primarily work preface arrangement is first to process a flat surface with the center bore fixed position with the right side flat surface and below big bore of two flat surface, again with center bore the fixed position processes the big bore that carry down.While processing is to use the boring machine boring bore.Regard these two bores as the basis finally, process the right-hand slot respectively with the thread bottom bore of the a.Whole processes the process chose to use to the drill machine, miller with the boring machine .The tongs chooses to use the appropriation tongs, clipping tight way as to move to clip tight, clip tight and dependable, operation convenience.Therefore produce the efficiency higher, be applicable to the large quantity measures, the flowing water is on-line to process.Can satisfy the design request.


Keywords Process the craft，F(xiàn)ixed position，Clip tight，Appropriation tongs
目 錄

摘 要 Ⅰ
Abstract Ⅱ

1 緒論 1
1.1課題背景 1
1.2夾具的發展史 1
1.3小結 2
2 撥叉80-08的加工工藝規程設計 3
2.1零件的分析 3
2.1.1零件的作用 3
2.1.2零件的工藝分析 3
2.2確定生產類型 3
2.3確定毛坯 3
2.3.1確定毛坯種類 3
2.3.2確定鑄件加工余量及形狀 3
2.3.3繪制鑄件零件圖 4
2.4工藝規程設計 4
2.4.1選擇定位基準 4
2.4.2制定工藝路線 4
2.4.3選擇加工設備和工藝設備 6
2.4.4機械加工余量、工序尺寸及公差的確定 6
2.5確定切削用量及基本工時 8
2.5.1工序1：粗銑Φ25H7的兩側面 8
2.5.2工序2：粗銑平下端面孔側面的工藝凸臺 9
2.5.3工序3：鉆Φ25H7的通孔 9
2.5.4工序4：擴Φ25H7的通孔 11
2.5.5工序5：鉸Φ25H7的通孔 12
2.5.6工序6：粗銑a、b面 12
2.5.7工序7：粗銑Φ60H12孔的兩面 14
2.5.8工序8：精銑Φ60H12孔的兩面 14
2.5.9工序9：粗鏜下端Φ60H12的孔 15
2.5.10工序10：半精鏜下端孔到Φ60H12 16
2.5.11工序11：粗銑16H11的槽 16
2.5.12工序12：半精銑16H11的槽 17
2.5.13工序13：鉆Φ20.50的孔 18
2.5.14工序14：攻M22×1.5的螺紋 19
2.5.15工序15：銑開Φ60H12的孔 20
2.6本章小結 21
3 專用夾具設計 22
3.1鏜孔夾具設計 22
3.1.1問題的提出 22
3.1.2夾具的設計 22
3.2銑槽夾具設計 25
3.2.1問題的提出 25
3.2.2夾具的設計 25
3.3鉆孔夾具設計 29
3.3.1問題的提出 29
3.3.2夾具的設計 30
3.4本章小結 35
結論 36
參考文獻 37
致 謝 38