畢業設計 基于ProE的手機外殼塑料模具設計
論文說明書共26頁，字?jǐn)?shù)總計：9471
資料簡介：
中期檢查樣表.doc
封面.doc
目錄.doc
畢業設計說明書.doc
開題報告.doc
畢業設計任務書.doc
A4-手機蓋.dwg
A4-定模座板.dwg
A4-型腔板.dwg
A3-推件板.dwg
A4-型芯固定板.dwg
A4-支撐板.dwg
A4-墊塊.dwg
A4-推桿固定板.dwg
A4-推板.dwg
A0-手機蓋注塑模具裝配圖.dwg
A4-型芯12.dwg
A4-型芯11.dwg
A4-型芯10.dwg
A4-型芯9.dwg
A4-型芯8.dwg
A4-型芯7.dwg
A4-型芯6.dwg
A4-型芯5.dwg
A4-型芯4.dwg
A4-型芯3.dwg
A4-型芯2.dwg
A4-型芯1.dwg
A4-動模座板.dwg
A3-裝配圖（備份）.dwg
摘 要

本文以手機外殼為例，介紹產品從調研，市場分析到最后設計模具的整個注塑模具設計的流程；首先，從試產調研和市場分析入手，通過對比，設計好自己的具有可行性的新產品方案；再用Pro/Engineer對產品建模；然后對產品進行MSC有限元分析，確定產品滿足受力要求后，再設計模具，并通過Pro/Engineer外掛的塑料顧問模塊來分析，確定最佳澆注口，分析模流情況，以達到最佳的充模效果。通過Pro/Engineer外帶的EMX模塊，進行模具的模架設計。最后把關鍵零部件的二維圖還有模具的裝配圖以圖紙的形式展現出來。根據企業調研，在企業的產品設計過程中，傳統的圖板繪圖設計和傳統的人工設計已被淘汰。取代而之的是使用 Pro/E或UGS 進行產品的全過程的設計。，選用Pro/E 這個軟件進行本課題的全過程設計，其中包括三維建模、模具芯腔設計、EMX模具模架設計，以及Pro/E 的工程圖功能。

關鍵詞：手機外殼，注塑模， Pro/E Wildfire 3.0，模具設計
Abstract

This massage Based on the mobile phone housing, for example, from research, introduce products to the market analysis and design of the mould injection mold design process, First, from the pilot research and market analysis, through comparing, design with good feasibility of new products plan, Reoccupy Pro/e to product modeling, Then to MSC finite element analysis, determine product to meet requirements, design force, and through the mold Pro/e plugin plastic consultant to determine the optimal analysis module, casting mold flow analysis, in order to achieve the best effect of stamping. Through the Pro/e EMX module, the periphery of the formwork design moulds. The key parts of the last of the two-dimensional chart and mould assembly drawings with the form. According to the investigation in the enterprise, the enterprise product design process, the traditional drawing graphics design and traditional artificial design has been eliminated. Replace the use and Pro/E or UGS are products of the whole design. Pro/E, choose the software process design of this project, including the 3d modeling, mold cavity design and EMX core mold design and formwork Pro/E of engineering drawing function

Keywords: cell phone casing, injection molding, Pro/E your e-zine 3.0, mould design
目 錄

中文摘要……………………………………………………………………………………… 1
英文摘要……………………………………………………………………………………… 2
目 錄……………………………………………………………………………………… 3
1 概述………………………………………………………………………………………… 1
1.1 手機外形的發展趨勢………………………………………………………………… 1
1.2 注塑模國內外研究現狀……………………………………………………………… 1
1.3 注塑模發展趨勢……………………………………………………………………… 2
1.4 傳統方法注塑模具的設計流程……………………………………………………… 3
1.5 基于Pro/E Wildfire 3.0注塑模具設計的概述……………………………………4
2 塑件工藝性分析…………………………………………………………………………… 5
2.1 塑料的分析…………………………………………………………………………… 5
2.2 塑件的分析…………………………………………………………………………… 5
3 澆注系統選擇及分型面確定……………………………………………………………… 7
3.1 分形面的確定………………………………………………………………………… 7
3.2 澆注系統的選擇……………………………………………………………………… 9
4 成型部位尺寸計算…………………………………………………………………………14
5 模塑仿真與開模仿真………………………………………………………………………16
5.1 模塑仿真………………………………………………………………………………16
5.2 開模仿真………………………………………………………………………………16
6 注塑機和標準模架的選擇…………………………………………………………………17
6.1 注塑機的選擇…………………………………………………………………………17
6.2 標準模架的選擇………………………………………………………………………19
7 加熱及冷卻系統的設計……………………………………………………………………21
7.1 加熱系統的設計………………………………………………………………………22
7.2 冷卻系統的設計………………………………………………………………………22
8 模具開合模分析……………………………………………………………………………23
結 語………………………………………………………………………………………24
參考文獻………………………………………………………………………………………25
附 錄………………………..