特殊損傷控制技術[外文翻譯].rar
特殊損傷控制技術[外文翻譯],包含中文翻譯和英文原文，內容詳細完整，建議下載參考！中文： 3535字英文： 9699字符引言本章簡介將用相關的生產炮孔來介紹爆破損傷區（bdt）概念。隨著開采區域的擴大，爆破損傷過渡區的也自動擴大，除非采用特別的技術例如線性鉆孔或者預裂爆破技術。這一部分將會討論這兩種技術。為了能更方便的討...
該文檔為壓縮文件,包含的文件列表如下:
內容介紹
原文檔由會員 xiaowei 發布
特殊損傷控制技術[外文翻譯]
包含中文翻譯和英文原文，內容詳細完整，建議下載參考！
中文： 3535字
英文： 9699字符
引言
本章簡介將用相關的生產炮孔來介紹爆破損傷區（BDT）概念。隨著開采區域的擴大，爆破損傷過渡區的也自動擴大，除非采用特別的技術例如線性鉆孔或者預裂爆破技術。這一部分將會討論這兩種技術。為了能更方便的討論損傷控制技術，看表10.7，在該表中概略的顯示了直徑從9-7/8英寸的裝滿炸藥炮孔的損傷區域。根據損傷的程度可以很方便的將損傷區域細分為三個區域。每個區域的范圍都是以到藥包中心的半徑來衡量。在這個表中的損傷區域的范圍（以炮孔直徑D描述的）和得到的相應的PPV值是使用銨油炸藥在中等強度的巖石中爆破得出的結果 ......
SPECIAL DAMAGE CONTROL TECHNIQUES
Introduction
In the introduction to this chapter the concept of a blast damage transition zone (BDT) was presented with respect to the production holes. As the pit expands outward, the BDT follows along automatically unless some special measures are taken such as line drilling or pre-splitting. These are two of the techniques which will be discussed in this section. To facilitate this discussion on damage control techniques, consider the BDT shown diagrammatically in Figure 10.7 for a fully-charged 9-7/8" diameter hole. It is convenient to subdivide the BDT into three zones based upon the level of damage. The extent of each zone is characterized by a radius from the center of the production charge. The zones, their extent (as expressed in terms of the hole diameter D) and the corresponding PPV values resulting when using ANFO in medium strength rock are assumed to be as follows ......
包含中文翻譯和英文原文，內容詳細完整，建議下載參考！
中文： 3535字
英文： 9699字符
引言
本章簡介將用相關的生產炮孔來介紹爆破損傷區（BDT）概念。隨著開采區域的擴大，爆破損傷過渡區的也自動擴大，除非采用特別的技術例如線性鉆孔或者預裂爆破技術。這一部分將會討論這兩種技術。為了能更方便的討論損傷控制技術，看表10.7，在該表中概略的顯示了直徑從9-7/8英寸的裝滿炸藥炮孔的損傷區域。根據損傷的程度可以很方便的將損傷區域細分為三個區域。每個區域的范圍都是以到藥包中心的半徑來衡量。在這個表中的損傷區域的范圍（以炮孔直徑D描述的）和得到的相應的PPV值是使用銨油炸藥在中等強度的巖石中爆破得出的結果 ......
SPECIAL DAMAGE CONTROL TECHNIQUES
Introduction
In the introduction to this chapter the concept of a blast damage transition zone (BDT) was presented with respect to the production holes. As the pit expands outward, the BDT follows along automatically unless some special measures are taken such as line drilling or pre-splitting. These are two of the techniques which will be discussed in this section. To facilitate this discussion on damage control techniques, consider the BDT shown diagrammatically in Figure 10.7 for a fully-charged 9-7/8" diameter hole. It is convenient to subdivide the BDT into three zones based upon the level of damage. The extent of each zone is characterized by a radius from the center of the production charge. The zones, their extent (as expressed in terms of the hole diameter D) and the corresponding PPV values resulting when using ANFO in medium strength rock are assumed to be as follows ......
