摘 要

生物醫學工程的迅速發展，帶來了人類醫療技術的革命。而病變、事故等原因導致髖關節功能喪失，給患者帶來了很大的不便。人工關節特別是人工髖關節置換術是一種能即刻緩解、消除關節疼痛，提高患者生活質量的成功手術。
但是置換術后的中遠期效果不能令人滿意，置入假體出現無菌松動等并發癥，導致手術失敗引起翻修。目前，雖然對人工關節松動的確切機理尚不清楚，但是致病因素基本可歸為兩大類：一為生物學因素，即松動由磨損顆粒引起；另一為機械因素，即松動由微動、壓力等引起。
本文利用圖像處理和計算機輔助設計技術，將股骨CT二維圖像進行三維重建，設計了解剖型假體，與股骨虛擬裝配后，通過有限元軟件（ANSYS）分析假體在步態載荷作用下的位移變化情況。假體的位移在二十微米左右，結合Jasty等人關于微動對假體松動影響的研究成果，證實解剖型假體具有較好的初始穩定性，有利于減少由于微動造成的假體松動。


關鍵詞：髖關節假體，步態載荷，有限元法，微動


















ABSTRACT

With the rapid development of biomedical engineering, it brings the revolution of medical technique. However, the loss of hip joint function caused by pathologic change, accident and so on makes patients inconvenient seriously. Joint replacement, especially hip joint replacement is a successful surgical procedure, which can release and eliminate the pain of joint, advance life quality of patients and so on.
But the long-term stability of the artificial joint is not satisfactory, with the aseptic loosening and other complications, which lead to the failure of the operation. At present, although the exact mechanism of loosening is not clear, many researchers consider that both the mechanics and the biology factors can cause the loosening, for example, fretting and wearing chippings.
On the basis of image Processing technique and computer aided design technique，three dimensional digital model of femur was reconstructed from CT data. An anatomical prosthesis is designed by Pro/E, virtual assembled with the femur. Through the finite element software (ANSYS), simulate the displacement of prosthesis according the gait loads. The displacement of prosthesis is about 20μm. According to Jasty’s research results, it proves that anatomical prosthesis has good initial stability, which can reduce the prosthesis loosening caused by fretting.


Key words：Hip prosthesis, Gait load, Finite element method, Fretting













目 錄

中文摘要 Ⅰ
ABSTRACT Ⅱ
1緒論 1
1.1引言 1
1.2人工髖關節的發展 1
1.2.1 人體髖關節的解剖結構和生物力學特點 1
1.2.2 人工髖關節及研究現狀 3
1.2.2.1 人工髖關節材料 3
1.2.2.2 人工髖關節設計 5
1.2.2.3 人工髖關節的固定 6
1.3 解剖型人工髖關節 7
1.4 本課題研究目的及內容 9
2股骨三維實體模型的建立 10
2.1 CT圖像數據的采集 10
2.2 CT圖像數據處理及輸出 11
2.3 股骨模型三維重建 13
2.4 本章小結 16
3 解剖型假體的設計 17
3.1 概述 17
3.2 假體的設計 17
3.3 假體與股骨的虛擬裝配 22
3.4 本章小結 22
4 假體在步態載荷作用下位移的有限元分析 23
4.1 引言 23
4.2 有限元分析 23
4.2.1 定義材料屬性 23
4.2.2 網格劃分 24
4.2.3 接觸設置 25
4.2.4 施加載荷與約束 28
4.2.5 求解器設置 31
4.3 察看結果 32
4.4 本章小結 33
5 結果分析 34
5.1 假體位移結果分析 34
5.2 微動對人工髖關節松動的影響分析 36
5.3 本章小結 37
6 結論與展望 38
6.1 全文工作總結 38
6.2 今后研究工作展望 38
致謝 39
參考文獻 40