加油口支座沖孔落料模具設計

包括論文，cad圖紙，答辯ppt


目
錄

前   言 1
一.  工藝設計 4
1.1． 零件的工藝分析 4
1.2.確定沖裁的工藝方案及模具的結構形式 5
二.  模具設計 7
2.1毛坯尺寸計算 7
2.2合理排樣和條件寬度 7
2.3主要工藝參數計算 8
2.3.1．各工序沖壓力的計算 8
2.3.2．凹模,凸模工作尺寸的計算 10
三．橡皮的設計和選用 13
四．確定各個主要零件的外型尺寸 15
4.1．凹模外型尺寸的確定: 15
4.2．凸模固定板和凹凸模外形尺寸的確定: 15
4.3．凹,凸凹模退料板外形尺寸的確定: 15
4.4模架．模柄和墊板的外形尺寸的確定: 15
4.5．計算模具的閉合高度: 16
4.6．確定所用沖床: 16
4.7．卸料螺釘．緊錐螺釘和銷釘?shù)倪x用 16
4.8．模具工作過程描述 17
4.9．模具圖樣設計 17
五. 模具的改進 18
總結 19
參考文獻 20
致    謝 21

【中文摘要】： 本次設計的課題是加油口支座沖孔落料模具的設計，此次設計主要針對沖壓工藝和沖模設計兩方面展開。首先針對模具的發展進行了一定得分析和詮釋?zhuān)约敖忉尨舜蔚脑O(shè)計內容；然后是工藝設計主要內容是對零件的分析和模具的選擇方法；其次是模具的設計；然后是橡皮的設計和選用；緊接著是確定各個主要零件的尺寸；然后對模具的改進進行了分析；最后總結了此次設計過程。
關鍵詞：    模具、模具選擇、橡皮、工藝設計、模具改進。

【Abstract】:  The project's name is the design of oil filler bracket piercing and blanking die. This design is mainly about two aspects, namely sheet metal forming technology and punch die design. It  analyses and interprets the development of mold,as well as explains the contents of this project; The main body of the technological design is about the analysis of  parts and the selection method of mold;  Becides it concerns the mold design and the design and selection of rubber;moreover it is about the determination of every parts' sizes and analysis of the improvement of mold; finally it summarizes the process of this design.’
    key words: mold, mold selection,  rubber,  technological design,  mold improvement