摘 要

本次畢業設計的題目是CA141左轉向節規程及工裝設計。我主要需要完成的包括加工工藝的安排以及兩種專用機床夾具設計。為了保證加工零件的精度同時節約成本和縮短加工周期以及提高加工效率，那么一個良好的工藝安排以及專用夾具的設計就是必不可少的了。在工藝的安排上不但要考慮合理的加工要求還要考慮到操作者以及加工機械的安全。同時夾具的設計上也要考慮到使用的安全性和經濟性以及安裝和拆卸上的方便性。設計一個良好的工藝工裝安排路線那么必須要經過對加工件的詳細分析以及周密的考慮后才能得出。所以分析問題是解決問題的關鍵，同時還要反復的調整，來尋求最好的一個路線。這樣才能讓工藝路線更加的完美，才能保證工件的加工精度和加工效率以及節約材料。

關鍵詞 轉向節；加工工藝；專用夾具；加工精度；工藝路線
















Abstract

The graduation design is the subject of CA141 car’s left steering process tooling. I mainly need to complete including Processing craft arrangement as well as special-purpose drill jig design.
In order to guarantee the processing components the precision Simultaneously saves cost and the reduction processing cycle as well as the enhancement processing efficiency, Then a good craft arrangement as well as unit clamp's design was essential. Not only in the craft arrangement must consider that the reasonable processing request also needs to consider the operator as well as processes machinery's security. Simultaneously jig's design also needs to consider the use in secure and efficient as well as the installment and the disassemblage conveniences. Designs a good craft work clothes arrangement route that to probably pass through to the job multianalysis,After as well as thorough consideration, can obtain. Therefore the analysis question solves the question key, meanwhile must the repeated adjustment, Seeks a best route. Seeks a best route to be able to let craft route even more perfect like this, can guarantee that the work piece the working accuracy and the processing efficiency as well as save the material.

Key word Steering ; Processing craft; Unit clamp; Working accuracy ; Craft route









目 錄

摘要 ……………………………………………………………………………………… Ⅰ
Abstract ………………………………………………………………………………… Ⅱ
緒論 ……………………………………………………………………………………… 1
1 零件的分析 …………………………………………………………………………… 2
1.1 零件的作用 …………………………………………………………………………… 2
1.2 零件的工藝分析 ……………………………………………………………………… 3
1.2.1 軸頸部分 …………………………………………………………………………… 3
1.2.2 法蘭部分 …………………………………………………………………………… 4
1.2.3 叉架部分 …………………………………………………………………………… 4
1.2.4位置精度要求 ……………………………………………………………………… 4
2 工藝規程設計 ………………………………………………………………………… 6
2.1 確定毛坯的制造形式 ……………………………………………………………… 6
2.2 基面的選擇 ………………………………………………………………………… 6
2.2.1 定位基準的選擇 …………………………………………………………………… 6
2.2.2 粗基準的選擇 ……………………………………………………………………… 6
2.2.6 精基準的選擇 ……………………………………………………………………… 7
2.3 工藝規程的設計原則 ………………………………………………………………… 7
2.4 制定工藝路線 ………………………………………………………………………… 8
2.5 機械加工余量、工序尺寸及毛坯尺寸的確定 ………………………………………12
2.6 確定切削用量及基本工時 …………………………………………………………15
3 夾具設計 …………………………………………………………………………… 31
3.1 拉床專用夾具設計 ………………………………………………………………… 31
3.1.1 問題的提出 ……………………………………………………………………… 31
3.1.2 夾具設計 ………………………………………………………………………… 31
3.2 鉆模夾具設計 ……………………………………………………………………… 33
3.2.1 問題的提出 ……………………………………………………………………… 33
3.2.2 夾具設計 ………………………………………………………………………… 33
總結 ……………………………………………………………………………………… 37
致謝 ……………………………………………………………………………………… 38
參考文獻 ………………………………………………………………………………… 39