摘 要

汽車驅動橋作為汽車的四大總成之一，它承載著汽車載荷以及車身和地面給予的力以及力矩。汽車驅動橋的結構形式和設計參數不但對汽車的可靠性和耐久性有很大的影響，而且對汽車的行駛性能也有直接的影響。所以它的性能好壞直接影響到汽車的整車性能的好壞。驅動橋的零部件繁多，其中包括了主減速器、差速器、橋殼以及車輪等。為了滿足目前載重汽車的快速、大噸位、高時效的要求，不但需要大功率發動機輸出大的扭矩，而且必須要搭配一個高效可靠的驅動橋。傳動效率高的單級減速驅動橋能滿足需求而成為了未來發展的主要方向。

設計方法主要是參照傳統的設計方法對驅動橋進行設計，主要是對主減速器和差速器的設計、參數的選擇設計、強度校核等方面。本文首先是簡單介紹選擇本課題的背景意義、目的以及本課題解決的問題，之后介紹主減速器的結構型式和安置方法以及對主減速器、差速器的參數選擇以及計算校核和對軸承的選擇以及校核。

關鍵詞：驅動橋；主減速器；差速器；橋殼

Abstract:One of the four assemblies of automotive drive axle as the car, it carries with auto loading and force and moment from the body and the ground. Automotive drive axle of the structure and design parameters of automobile not only has great effect on reliability and durability, and performance of vehicles has direct influence. So its performance is good or bad directly affect the car's performance is good or bad. The components of drive axle is various, including the Lord reducer, differential and axle housing, and wheels, etc. In order to satisfy the fast truck, large tonnage, high aging, not only need high power engine output torque, but must be with an efficient and reliable drive axle. Transmission efficiency of single reduction drive axle can meet the demand and become the main direction of future development.

Design method mainly with reference to the traditional design method of drive axle design, mainly for the design of the main reducer and differential, the choice of parameter design, strength check, etc. This article first is simple introduced to choose the background significance, the purpose of this topic, and this topic to solve the problem, introduces the main reducer to the structure and placement method and parameter selection and calculation for the main reducer, differential and the choice of bearing and respectively.

Keywords: drive axle；differential bridge；main reducer；shell

目 次

摘要 I

Abstract

1  緒論 1

1.1 引言 1

1.2 研究的基本內容 1

2  主減速器設計 3

2.1 主減速器齒輪類型 3

2.2 主減速器的減速型式 3

2.3 主減速器錐齒輪的支承型式及安置方法 4

2.3.1 主動錐齒輪的支承型式及安置方法 4

2.3.2 從動錐齒輪的支承型式及安置方法 4

2.3.3 主減速器的軸承預緊及齒輪嚙合調整 4

2.4 主減速器的參數選擇與設計計算 4

2.4.1 主減速比的確定 5

2.4.2 主減速器齒輪計算載荷的確定 5

2.4.3 主減速器齒輪基本參數的選擇 7

2.4.4 主減速器軸承的計算 12

3  差速器設計 18

3.1 對稱式圓錐行星齒輪差速器的結構 18

3.2 對稱式圓錐行星齒輪差速器的設計 18

3.2.1 差速器齒輪的基本參數的選擇 18

3.2.2 差速器齒輪的幾何計算 20

3.2.3 差速器齒輪的強度計算 21

4  驅動半軸的設計 24

4.1 全浮式半軸計算載荷的確定 24

4.2 全浮式半軸的桿部直徑的初選 25

4.3 全浮式半軸的強度計算 25

4.4 半軸花鍵的強度計算 26

5.  驅動橋殼的簡單介紹 27

5.1 驅動橋殼結構選擇 27

5.2 驅動橋殼的作用 27

6.  結論 28

參考文獻 28

附錄1 28