十字軸式萬向節設計.rar
十字軸式萬向節設計,一、設計題目 十字軸式萬向節二、設計參數車重:1590kg 變速器一擋傳動比:4.17最大載重:420kg最大變矩系數:2.6傳動軸支撐長度:855mm發動機最高轉速:6200rpm輪胎規格:215/55-r17主減速器傳動比:3.909發動機最大轉矩:242nm后軸承載質量:1237kg摘 要本次設...
該文檔為壓縮文件,包含的文件列表如下:


內容介紹
原文檔由會員 sa184858105 發布十字軸式萬向節設計
一、設計題目 十字軸式萬向節
二、設計參數
車重:1590kg 變速器一擋傳動比:4.17
最大載重:420kg 最大變矩系數:2.6
傳動軸支撐長度:855mm 發動機最高轉速:6200rpm
輪胎規格:215/55-R17 主減速器傳動比:3.909
發動機最大轉矩:242N•m 后軸承載質量:1237kg
摘 要
本次設計主要對十字軸式萬向節進行了初步的設計。
本文對十字軸式萬向節的發展概況進行了綜合闡述,對幾種萬向節進行了分類介紹,對十字軸萬向節的結構進行了系統的分析,并對并在某一車型的基礎上進行了十字軸式萬向節的簡單設計,按傳遞扭矩初步選取了十字軸相應的尺寸并進行了校核,依據其基本結構確定了其他結構的尺寸并進行了初步的校核,最后用ug軟件對十字軸式萬向節進行了繪圖,最后又介紹了了十字軸式萬向節的技術要求和保養等等。
關鍵詞:萬向節;設計;傳動軸
Abstract
The design of the main shaft type universal joint preliminary design.
In this paper, the cross axis of universal joint development survey of the comprehensive elaboration, several universal joint of the classified introduction, the universal shaft structure of the system is analyzed, and the in a car and carried out on the basis of the universal shaft type of simple design, transfer torque according to preliminary selection the axis of the of size, according to the basic structure to determine the size of the other structure and the preliminary check, the last of the shaft with ug software of the universal joint drawing, finally it is also introduced the shaft type of universal joint technical requirements and maintenance, etc.
Key words: Universal joint; Design; Transmission shaft
目 錄
1引言 1
1.1各種萬向節簡介 1
2萬向節結構方案確定 5
2.1設計已知參數 5
2.2十字軸設計思路 5
3十字軸萬向節 6
3.1十字軸式剛性萬向節的構造及潤滑 6
4十字軸式萬向節設計 7
4.1傳動載荷的確定 7
4.2十字軸的選取與校核 8
4.3十字軸萬向節的軸承的選取與校核 11
4.4萬向節凸緣叉的設計 13
4.5螺紋直徑的選擇 14
4.6其他零件的選取 14
5萬向節的使用材料 16
6結論 17